HTC-1 Digital Temperature and Humidity Meter New Model

Temperature hygrometer user manual

Product Specifications

Temperature measurement range:-10℃～ +50℃(-14℉～+122℉)

Temperature measurement accuracy:±1℃(1.8℉)

Temperature resolution:±0.1℃(0.2℉)

Humidity measuring range: 10%～99% RH

Humidity measuring accuracy:±5% RH

Humidity resolution: 1%

Battery: AAA 1.5V

Basic functions

Temperature / Humidity

℃ /“F temperature switch display

The maximum / minimum temperature and humidity memory function

12/24 hour clock

The whole point timekeeping function

Daily alarm

Calendar display

How-to

1.Pushed by the rear direction of the battery door, battery, and then replace the

Batterydoor, the machine can be used.

2.Key features:【MODE】switch the clock and alarm display mode/set the current

clock, alarm clock, 12 or 24 hour clock, date;【ADJ】adjust the value is set to the

project;【MEMORY】display memory in the highest & lowest temperature and

humidity value/clear memory of the maximum & minimum temperature and humidity

values;【℃ /“F switching temperature units】℃(degrees Celsius)or℉(F)

display;

3.In the initial state, press【MODE】2 seconds, minutes and seconds the current

Time the number of start flashing, press【ADJ】few minutes and seconds can be

Adjusted continuously press【MODE】were set to “Clock”,”12/24”,”month(M)”,

“Day (D)”.

4. In the current clock mode(clock and minutes flash time between the two points

Per second), press【MODE】once, switch the display for the alarm clock mode

(clock and minutes between two points in not flashing),then press【ADJ】to

Switch“alarm”(Alarm) function/“The whole point of time”()function switch, and

Then press【MODE】2 seconds, you can set the alarm time, and start the“whole

point of time”function, ()symbol appears.

5. In alarm mode, without any operation automatically after one minute then return

to the current clock, then press to switch to the【ADJ】calendar display, 3 seconds

automatic ally returns the current clock, pressbutton to display the

temperature/humidity Last a clear(CLEAR) since the maxim um/minimum.

6.【MEMORY】can be displayed by the memory of temperature/humidity

Maximum(MAX)and minimum(MIN), press and hold【MEMORY】more than

7.In the bracket℃and℉conversion key

2 seconds to clear the maximum/minimum.

温湿度计用户手册

产品规格

温度测量范围：-10℃~+50℃ (+14℉~+122℉)

温度测量精度：±1℃（1.8℉）

温度分辨率：±0.1℃（0.2℉）

湿度测量范围：10%~99%RH

湿度测量精度：±5%RH

湿度分辨率：1%

使用电池：AAA1.5V

基本功能

温度/湿度显示

℃/℉温度切换显示

最高/最低温湿度记忆功能

12/24小时制时钟

整点报时功能

每日闹钟功能

日历显示功能

操作方法

1． 依机背指示方向推开电池门，装上电池，然后装回电池门，该机即可用。

2． 按键功能：【MODE】切换时钟与闹钟显示模式/设定当前时钟、闹钟、12或24小时制，日期；【ADJ】调整被设项目的数值；【MEMORY】显示记忆中的最高&最低温湿度值/清除记忆的最高&最低温湿度值；【℃/℉】切换温度单位以℃（摄氏度）或℉（华氏度）显示；【RESET】清除所有设定&记忆值，返回初始状态。

3． 在初始状态下按住【MODE】2秒，当前时间的分秒数开始闪动，按【ADJ】可以调节分秒数，连续按【MODE】可以分别设定“时钟”、“12/24”、“月（M）”、“日（D）”。

4． 在当前时钟模式下（时钟与分钟之间的两点每秒闪动一次），按【MODE】一次，切换显示为闹钟模式（时钟与分钟之间的两点不闪动），此时按【ADJ】可以切换“闹铃”（Alarm）功能/“整点报时”（）功能的开关，再按住【MODE】2秒，可以设定闹铃时间，同时启动“整点报时”功能，（）符号出现。

5． 在闹铃模式下，若无任何操作则一分钟后自动返回当前时钟，此时按一次【ADJ】切换至日历显示，3秒后自动返回当前时钟，按【MEMORY】钮，显示温/湿度最后一次清除（CLEAR）以来的最大/最小值。

6． 按【MOEMORY】可以显示记忆的温/湿度最大值（MAX）和最小值（MIN），按住【MEMORY】超过2秒可以清除最大/最小值。

7.支架内按键F°/C°转换

注意事项

1. 1.      若该机出现任何不良，重新装上电池;
2. 2.      电池用完后请放回政府指定地点。