Производители поставляют Пескоструйный шлем с регулируемой температурой системы фильтрации активированного угля запатентованные продукты Большие выгодно

                                供养头盔式空调防护系统说明书

               Manual of air conditioning protection system for prostration helmet

               简介及概述Introduction and Overview

       我公司是生产研发头盔防护系列配套产品的专业厂家，主要作用是喷砂工作时防止飞溅的磨料和喷砂产生的粉尘及噪音。是喷砂作业用品，保护工作人员免受尘对肺的伤害。适用于电弧喷涂，喷涂，防腐工程，化工，金属防腐，玻璃、五金大型切割，破碎，研磨，清灰等恶劣特殊场所施工需求的理想产品。远销国内外，深受好品！     Our company is a professional manufacturer of helmet protection series supporting products. The main function of our company is to prevent splashing abrasive and dust and noise caused by sand blasting. It is necessary for sandblasting operation to protect the workers from dust to lung injury. Suitable for arc spraying, spraying, anti-corrosion engineering, chemical industry, metal anti-corrosion, glass, hardware large cutting, crushing, grinding, ash cleaning and other bad special place construction requirements of ideal products. Sold at home and abroad, deeply good products!

一．防护服(Protective clothing)

       本产品采用高强度的ABS材质，一次成型；无毒无味，现货有红色和黄色，外观颜色艳丽；进气口配有消音装置，避免强气流进入时产生噪音；内设有进气导流槽，让气流均匀分布到四周，主流到镜框前，消除呼吸的气流，使其视线更清晰，避免气流直吹头部，造成不适；整体设计舒适通风效果科学合理，顶部配有安全头盔软塑减震调节网及海绵衬垫，大小可自行调节，使其头带感觉舒适；头套带特质无毒硅胶供气管，柔软耐弯曲；前面视野开阔，采用大小紧扣合密封，卸拆方便，不脱服装可直接拧开更换视窗镜片；颈部配有松紧封口，密封性更强，前后披肩合扣，穿戴方便。该产品具有耐用、安全、环保、舒适、方便、密封性能好等特点。This product adopts high strength ABS material, and it is formed in one time. Non-toxic and tasteless, spot red and yellow, the appearance of color gorgeous; The air inlet is equipped with noise-cancelling device to avoid noise caused by strong airflow entering; It is provided with an air intake guide slot to evenly distribute the air around and the main flow to the front of the picture frame, so as to eliminate the breathing air, make the line of sight clearer, and avoid the discomfort caused by the air directly blowing on the head. The overall design of comfortable ventilation effect is scientific and reasonable, the top is equipped with safety helmet soft plastic shock-absorbing adjustment network and sponge gasket, the size can be adjusted by oneself, make the headband feel comfortable; The head cover with characteristic non-toxic silica gel air supply tube, soft and bending resistant; The front view is wide, the size is tightly sealed, easy to disassemble and disassemble. The lens of the window can be changed directly without taking off the garment. The neck is equipped with an elastic seal for stronger tightness, and the front and rear shawl is fastened, making it easy to wear. The product has the characteristics of durability, safety, environmental protection, comfort, convenience and good sealing performance.

头盔型号分为HY-02A和HY-02B两款（Helmet models are divided into HY-02A and HY-02B）：

HY-02A：

为广阔视窗，采用双层PVC镜片，PVC镜片厚度常规配置为0.5mm厚度，出厂时配有双面保护膜，使用前应撕掉双面保护膜。   For wide Windows, double-layer PVC lenses are adopted. The thickness of PVC lenses is normally configured as 0.5mm. Double-side protective film shall be removed before use.

HY-02B：

为内层1mm厚度PVC镜片，出厂时配有双面保护膜，使用前应撕掉双面保护膜，外层为玻璃镜片，两层镜片必须配套同时使用，严防玻璃破碎对人体造成伤害。The inner layer is 1mm thick PVC lens, which is equipped with double-sided protective film when leaving the factory. The double-sided protective film should be removed before use, and the outer layer is glass lens.The two layers of lens must be used together to prevent the breakage of glass from causing harm to human body.

防护服从款式上分为：披肩式，披风式，上衣式，连体式；

Protective obedience on design is divided into: shawls, ponchos, coat, even the postures

*披肩式（Cape type:）：穿戴简单，轻便；Wear simple, light;

*披风式（Cape type）：可以保护个人局部，特别是喷砂作业，可以抵制反弹回来的钢砂对人体的疼痛感和伤害，从头盔顺势而下气流会顺至前胸后背；Can protect the individual local, especially sand blasting operation, can resist the steel shot of bounce back pain and harm to human body, will arrange to go down those routes from the helmet airflow to the chest back;

*上衣式（The upper jacket type）：可以保护个人上半部，特别是喷砂作业，可以抵制反弹回来的钢砂对人体的疼痛感和伤害，从头盔顺势而下气流会顺至整个上半身；Can protect the individual, especially sand blasting operation, can resist the steel shot of bounce back pain and harm to human body, to go down those routes from the helmet airflow will be suitable to the entire upper body;

*连体式（Even）：可以保护个人全身，特别是喷砂作业，可以抵制反弹回来的钢砂对人体的疼痛感和伤害，从头盔顺势而下气流会顺至全身；Can protect the individual body, especially the sand blasting operation, can resist the steel shot of bounce back pain and harm to human body, to go down those routes from the helmet airflow will be suitable to the whole body;

二．温度调节器(The temperature regulator)

空气温度调节器以过滤后的压缩空气为能源，气流转化为冷气和热气，生态、洁净型的冷热发生器，空气温度调节器结构简单可靠。经过手柄调节可以得到温度适中，感觉舒适的呼吸空气，当压缩空气压力为0.4-0.8MPa时，调节温度范围为10℃-40℃。本空气温度调节器适用于喷砂行业以及表面处理行业， 温度调节器不能完全关闭，因此操作人员总是至少有最低所需的空气量的呼吸，保持头盔里有足够的压力和供气量。 温度调节器带有一个管带，调整环，以适应到54英寸的腰围。持久耐用的扣可固定和戴手套的手松绑。帮助通过保持喷砂工作人员带喷砂头盔在炎热的天气感到凉爽和在寒冷的天气感到温暖，不管在寒冷的冬天，还是酷热的夏季中都可以使用。可以提高生产力，耐用，轻巧舒适。Air temperature regulator to the filtered compressed air for energy, air currents into air conditioning and heat, ecology, clean type cold heat generator, air temperature controller structure is simple and reliable. After shearing can get temperature is moderate, the feeling is comfortable breathing air, when the compressed air pressure is 0.4 to 0.7 MPa, adjust the temperature range of 10℃and 40℃. This air temperature controller is suitable for sand blasting and surface treatment industry, temperature regulator can't completely shut down, so the operator is always at least the minimum required amount of air breathing, keep enough pressure and throughput in the helmet.Temperature controller with a belt, adjusting ring, so as to adapt to the waist to 54 inches. Durable button can be fixed with a gloved hand. Help by keeping with sandblasting sand blasting staff helmet feel cool in the hot weather and warm in cold weather, no matter in the cold winter, or hot in the summer can be used.Can improve the productivity, durable, light and comfortable.

三．罐式精密过滤器（Tank Type Precision Filter）

本产品滤芯采用精梳棉、活性炭、氧化铝等科学组合深层型结构进行过滤。有效序列捕获水、油气味和有机气体。广泛适用于食品、医药、电子、化工等行业。

The filter of this product is made of combed cotton, activated carbon, alumina and other scientific combination of deep structure filter. Effective sequence capture water, oil smell and organic gas. Widely used in food, medicine, electronics, chemical and other industries.

1、体积小，过滤精密度高(Small size,high precision filte)r；

2、通流的能力大，压力损失小(High flow ability,low pressure loss)；

3、易于清洗、更换(Easy to clean、replacement)。

注意事项(Note)：

由于活性炭过滤器的活性炭吸附功能具有一定的饱和值，当达到饱和吸附容量时，活性炭滤池的吸附功能将大大降低，因此需要注意分析活性炭的吸附能力，及时更换（建议4-6个月）。Because of theactivated carbon filter activated carbon adsorption function has a certain saturation value,when the saturated adsorption capacity is reached,the adsorption function of activated carbon filter will be greatly reduced,so need to pay attention to the analysis of the adsorption capacity of activated carbon,replace it timely(advice4-6month).

                     使用说明书Operating instruction

    常规的压缩空气是不能直接用于我们正常呼吸的（压缩含有大量的微颗粒，压缩机中作中的油份，高压高热产生的有害气体等），由于喷砂，喷涂行业工作环境特殊，工人工作的完全密封环境，尤其是夏季，所以很有必要配备空调系统，防护主要以头部呼吸为主，故采用高强度ABS为材质的完全封闭的头盔，效果为佳。Conventional compressed air can't be directly used in our normal breathing (compression contains a large number of small particles, as the oil in the compressor, high pressure heat produce harmful gases, etc.), because of the sand blasting, spraying industry special working environment, workers work completely sealed environment, especially in the summer, so it is necessary to equipped with air conditioning system, protection mainly head to breathe, so high strength ABS completely closed to the helmet, the effect is better.

首先在25（4分1/2“英寸管螺纹内牙）处接入压缩空气，可采用，管牙接，宝塔喉箍接，快插接或自锁式接口均可，24初过滤去压缩空气中的油水及淤垢，26要经常排放，26和27最好是每班（工作约10小时排放一次）气体经23，22，21，20，19，18科学组合至，深层型结构进行过滤。有效序列捕获水、油气味和有机气体后，顺15（4分，1/2英寸管螺纹内牙）处接入压缩空气，可采用，管牙接，宝塔喉箍接，快插接或自锁式接口均可，16压力显示在4-8Mpa之间为正常工作压力，否则17随之安全失效，14尽可能采用无毒无害的软管（应过滤器为固定放置，所以14要根据工作场所大小确定长短，，随着软管的加长，软管的内径应随之加大，确保空气的流量和压力送至调温器（10米内可采用软管内径大于8-10mm ，10-30米应采用软管内径大于10-12mm，30-50米应采用软管内径大于12-14mm），13为自锁式公母快插是自锁接头（公），14软管上根据软管的材质，大小和工作习惯可配置相应的接头来配套13，可采用，管牙接，宝塔喉箍接，快插接或自锁式接口均可，当然也可在购买时同厂家联系配套接头，或者要求13处改变成理想接头。12可根据个人的胖瘦自行调节长短，置于腰间，可根据自身要求左右扭转调节11至 理想温度，10为冷热气转换出口，当11旋至“热”时，10排放的为冷气，当11旋至“冷”时，10排放的为热气，当11旋至最“冷”时，10排放的热气温度较高（40℃左右），注意烫伤，9为（6分3/4“英寸管螺纹外牙），2为正常配置调温器和防护头盔软管（内径13mm,长度700mm，硅胶软管，内置不锈钢钢丝圈，防止软管弯曲打折阻碍供气，外套有保温软管层，确保温度的流失），头盔进口处装有消声器，消除强气流瞬间进入产生的噪音，气流通过1有序将进入气体主流至头盔面部，让气流均匀分布到四周，主流到镜框前，消除呼吸的气流，使其视线更清晰，避免气流直吹头部，造成不适，气流在完全封闭的头盔内顺至脖子到全身，5有两层镜片，内层为固定镶嵌在头盔上，其主要作用是保证密封，不易更换，所以当外层镜片模糊后须即使更换外层镜片，确保不伤及内层镜片，外层镜片在出厂是附有双层保护膜，使用时打开3，揭开4，取出外层镜片，撕去双层保护膜，双手尽量接触镜片的视线范围，确保镜片的清晰度，头盔内配有大小可调头戴网型头箍，头箍配有可调下巴带，头顶配有隔音保护棉，6为内藏是喉箍锁环，将防护服牢固的锁于头盔卡槽内，确保防护服和头盔密封连接，7为披风是防护服，脖子处配有宽松式松紧，有效隔离外界沙尘飞溅入内，左右腋下配有8，4个卡口，穿戴方便，当然7也有披肩式，上衣式，连体式，望购买时根据自身情况说明。First in 25 (4 1/2 "inch pipe thread tooth) connected to the compressed air, can be used, the pipe threads, pagoda throat hoop, fast splice or self-locking type interface, 24 prefiltration scale to oil and water from compressed air and sediment, 26 always emissions, 26 and 27 is best per shift gas emissions (work about 10 hours) the scientific combination to 23,22,21,20,19,18, deep filtering type structure. Effective sequence capture after water, oil and gas and organic gas, shun 15 (within four points, 1/2 inch pipe thread tooth) connected to the compressed air, can be used, the pipe threads, pagoda throat hoop, fast splice or self-locking type interface, 16 pressure display as normal working pressure between 4-8 Mpa, 14 or 17 security fails, then as far as possible, using non-toxic harmless hose (14 should filter as the fixed place, so, the length should be determined according to the size of workplace, as the lengthen of hose, hose diameter should be increased as, To ensure that the air flow and pressure to the thermostat (within 10 meters can use hose diameter greater than 8 to 10 mm, 10 to 30 meters should use hose diameter greater than 10-12 mm, 30-50 m should use hose diameter greater than 12-14 mm), 13 for a quick plug is self-locking type male female self-locking connector (male), 14 according to the material of hose, hose size and corresponding joint work habits can be configured to form a complete set of 13, can be used, the pipe threads, pagoda throat hoop, fast splice or self-locking type interface, when buy, of course, also can contact with matching joints, or require 13 change into the optimal joint. 12 can be used to adjust the length according to the individual, in the waist, can be adjusted according to their own requirements about reverse 11 to the ideal temperature, 10 for cold and hot gas conversion export, when 11 back to "hot", 10 emissions for air conditioning, when 11 back to "cold", 10 emissions for the heat, when 11 back to the "cold", 10 emissions of hot air temperature is higher (around 40 ℃), pay attention to scald, 9 for six points (3/4 "inch pipe thread teeth), 2 protective helmet as normal configuration thermostat and hose (13 mm diameter, the length of 700 mm, silicone hose, built-in stainless steel wire circle, Prevent hose bend discount hinder the air supply, coat layer insulation hose, ensure that the loss of temperature), helmet inlet is equipped with muffler, eliminate strong airflow in an instant into the noise, air flow through the orderly will enter the mainstream gas to 1 helmet face, let air flow uniform distribution to four weeks, the mainstream to the front of the picture frame, eliminate breath of air, make it more clearly the line of sight, avoid air blow to the head, cause discomfort, airflow inside the helmet in completely closed to the neck to the body, may have two layers of lenses, the inner layer for fixed inlaid on the helmet, its main function is to ensure that the seal, not easy to change, so when the outer lens blur to be even change the outer lenses, Lenses to ensure it does not hurt and the inner, outer lens in factory is with double protective film, when using open 3, uncover 4, remove the outer lenses, tore to double protective film, hands contact lenses sight as far as possible, to ensure that the lens of the definition, type size inside the helmet is equipped with adjustable head wear network head hoop, head band is equipped with adjustable jaw belt, cotton head is equipped with sound insulation protection, 6 to hide inside is throat hoop lock ring, lock protective clothing firm in helmet card slot, sealing connection, ensure the protective clothing and helmet 7 as the cloak is protective clothing, neck with loose elastic, effective isolation dust flying in the outside world, left and right axillary is equipped with 8, 4 a bayonet, easy to wear, Of course, there are also shawl type, jacket type, even style, when you want to buy according to their own situation.            以上仅供参考，详情请致电海圆机械销售人员，020-82881087。

公 司 简 介

我公司是针对表面处理行业和服装工艺行业研究，推广的专业科技型企业。公司以雄厚的技术实力和优良的产品质立足于珠三角地区，产品远销国内外。公司所生产的表面处理设备和服装专用加工设备，主要是引进美国，意大利，台湾，韩国等先进技术的基础上，而结合行业实际生产情况研制的先进设备。主要具有：可超作性强、投资少、能耗低、效率高等特点。及各种设备配件、耗材，等并提供维修及售后服务。

我公司自主研发的供氧头盔式防护服﹑呼吸调温器﹑呼吸过滤器配套产品，具有技术含量高，设计安全，合理，环保等特点，深受国内外好评！

公司地址：中国广东省增城市新塘镇港口大道102号

电话：020-32871073  020-82881087

传真：02032871073

网址：http//:www.hyjx020.com

     http//:www.chuangyuan020.cn.alibaba.com

邮箱：13802838510@139.com       QQ;1113075316

全国免费统一热线：4000805090