HTC-8A новые светящиеся часы температуры и влажности

HTC-8A夜光温湿度计 时钟说明书

 基本特性:

     1.温度，湿度，年月日，时钟，同屏显示

     2. 12/24小时制的时钟

     3.每日闹钟 。整点报时功能

     4.℃/℉温度显示 。温度与湿度最高最低记忆

     5.夜光功能

     6.温度测量范围：0℃~50℃ (-32℉~122℉)  

     7.温度分辨率显示：0.1℃ (0.2℉) 

     8.温度测量精度：±0.5℃ (0℃~50℃),其他±1℃

     9.湿度测量范围：10%RH~99%RH 

 操作说明:

     1.夜光的开启，按一按有灯光图标按键点亮夜光，5秒后自动熄灭。

     2.温度单位的切换

      在机身背面按[℃/℉]温度单位键切换温度显示单位。

     3 .记忆的查看与清除

     在机身背面按[MAX/MIN]记忆键可查看记忆中最高(MAX)/最低(MIN)温湿度                   值，在显示最高(MAX)/最低(MIN)温湿度值时，长按[MAX/MIN]记忆键清除记忆中的最高(MAX)/最低(MIN)温湿度值。

     4.日期时钟的设定

     在显示时钟的时候，长按[MODE]模式键开始依次设定时钟的分钟→小时

      12∕24小时制→年→月→日，按[ADJ] 调整键调整。

     再按[MODE]模式键确认设定的时钟与日期

     5.闹钟时间的设定

     在显示时钟的时候，短按[MODE]模式键切换到闹钟的显示，再长按[MODE]

     模式键开始依次设定闹钟的分钟→小时，按[ADJ] 调整键调整。

     再按[MODE]模式键确认设定的闹钟时间。

     6.闹钟与整点报时的开启与关闭

     在显示时钟的时候，短按[MODE]模式键切换到闹钟的显示，按 [ADJ]调整

     键开启/关闭闹钟或整点报时，顺序是：闹钟开－>整点报时开－>闹钟与整

     点报时同时开－>闹钟与整点报时都关。

 注意事项：

     1.该机为精密仪器，用户自行拆卸造成的损坏不在保修范围内。

     2.电池用完后请放回政府指定回收点。                                                                                                                                            

HTC-8 luminous temperatureand humidity meterclock manual

The basicfeaturesof：

1. 1.    Temperature, humidity, date(year、mouth、day), clock, with screen display
2. 2.    Clock for 12/24 hours
3. 3.    Daily alarm。The whole point timekeeping function
4. 4.    ℃/℉temperature display。The maximum and minimum memory of temperature and humidity
5. 5.    Luminousfunction
6. 6.    Temperature measurement range：0℃~50℃(-32℉~122℉)
7. 7.    Temperature display resolution：0.1℃(0.2℉)
8. 8.    The temperature measurement precision:±0.5℃(0℃~50℃),others±1℃
9. 9.    Humidity measurement range: 10%RH~99%RH

Operating instructions：

1. 1.    The luminous opens：Press the button of light icon to lit luminous, automatically extinguished after 5 seconds.
2. 2.    Switching temperature unit:

Press the [℃/℉] buttonto switch temperature display unit.

3.Checkand clean the memory:

  Press the [MEMORY] memory button can check the maximum (MAX)/minimum (MIN) temperature and humidity value in the memory. When see Maximum (MAX)/ minimum (MIN) temperature and humidity value in display, press and hold the [MEMORY] memory button to clean the maximum (MAX)/minimum (MIN) temperature and humidity value in the memory.

4. The date and clocksetting:

When display the clock,press hold the [MODE] buttonstart to set the clockfollowed by minutes→hours→12∕24hours→year→mouth→day, press the [ADJ] key to adjust, then press the [MODE] button to confirm the clock and date.

5.The alarm time setting:

  When display the clock,press [MODE]buttonto switch to the alarm display,and then press and hold the [MODE] button start to set thealarm timefollowed byminutes→hours, press the [ADJ]buttonto adjust. Then press the [MODE] button again to confirm the alarm time setting.

6.The alarm clock and the whole point timekeeping opening and closing

  When display the clock,press [MODE]buttonto switch to the alarm display, and then press the [ADJ]buttonto open and close alarm clock or the whole point timekeeping, followed by the alarm clock opened－>the whole point timekeeping opened－>both the alarm clock and the whole point timekeeping opened－> both the alarm clock and the whole point timekeeping closed.

Note:

1. This machine for precision instruments, users to remove the damage is beyond the scope of the warranty.

2. The battery after use, please back the government designated collection points.