GoBozor ga xush kelibsiz
Универсальный 12 В 24 В 220 В наружный светодиодный сигнальный светильник стробоскоп-вспышка настенный Открыватель двери аварийный
Price section
dan boshlab
209 336 so'm
Kafolatlangan yetkazib berish muddati
Agar biz 45 kun kechiksak, buyurtmani bepul olasiz. Batafsil
Har doim siz bilan aloqada
Biz har kuni savollarga har qanday savollarga javob beramiz.
To'lovni qulay usulda xavfsiz qiling
Biz to'lovlarni turli xil usullarda qabul qilamiz.
Bo'lib to'lash mavjud
Mahsulot haqida
Xususiyatlar
- Происхождение
Китай
- Длина
85 мм
- Модель держателя лампы
0
- Номинальное напряжение
AC/DC 12-265V
- Номинальная мощность
1,5
- Пункт Нет.
Предупреждающий световой сигнал
- Тип
Светодиодная сигнальная лампа
- Марка
Другие
- Цвет
Оранжевый
- Интенсивность центрального освещения
0
- Импорт или нет
Нет
- Индивидуальная обработка
Нет
- Номер заказа
Светодиодная сигнальная лампа
- Иметь авторизованные частные бренды
Нет
Tavsif
价格可谈，欢迎咨询
通用12V 24V 220V户外LED信号报警灯频闪闪光灯壁挂式开门器紧急警告灯
Safety Instruction
1.For security, please read the user manual carefully before initial operation;
2.Please be sure the power is off before connecting, the product is produced without fuse;
3.This system must not endanger life or property during the running failure or its security risks
have been eliminated.
Specification
Working voltage: 12-265V AC/DC
Loading capacity: 1.5W
Weight: 156g
Flashing frequency: 1Hz
Installation method: Vertical/horizontal
Working temperature: -20°C~+60°C
Protection level: IP54
Size: 60*85mm
Notice：
1,Terminal 1 is for connectino thepower input; working voltage is 12-265VAC/DC.
2,Terminal 2 is for connecting the antenna of RF controller to extend the effective working distance
Instruction:
After power the lamp on, LED will start fashing in 1HZ(default setting).
sW1 is the switch for selecting flashing or on mode of the lamp.CAP short connectsthe 2 pins; the lamp is in flashing mode. Remove the CAP from 2 pins, the lamp is inon mode.
Be Careful, the whole board includes the components are with high voltage. Alwaysmake sure power is off before you open the cover
Installation
Open the package; take out the products and all the accessories. Removing the antenna by rotatinganticlockwise.
Mark 2 holes on the wall by using the fixing hole of bracket.
Drilling two 6mm diameter holes and one 10mm diameter hole. Then put the expansion plug intothe 6mm diameter holes. Put the wires through 10mm diameter hole.
Put the power wire and antenna through the cable holes in the holder. And fix the holder to thewall by provided 4mm*30mm self-taping screws.
Connect the wire and antenna to the correct terminals.
Put the cover back and make sure the cover is fastened with the bottom base without any gap.Then screw the antenna up and turn clockwise to make it tight.
Always install the holder and lamp upright to the ground. Horizontally installation may cause therain go inside the lam and damage the board.
Mutiple Voltage Flash Lamp
Antenna This is used to extend the effective distance of controller Waterproof and dustproof It is made of plastic material IP 54 .
wide range of uses:
Garage doors, Electronic gates, Barrier gates, sliding doors, automatic doors, rolling doors, shutters
Electrical appliances/Home automation i.e. lights, Alarm system, access control system
Barcha xususiyatlar
Xususiyatlari
- Происхождение
Китай
- Длина
85 мм
- Модель держателя лампы
0
- Номинальное напряжение
AC/DC 12-265V
Tavsif
价格可谈，欢迎咨询
通用12V 24V 220V户外LED信号报警灯频闪闪光灯壁挂式开门器紧急警告灯
Safety Instruction
1.For security, please read the user manual carefully before initial operation;
2.Please be sure the power is off before connecting, the product is produced without fuse;
3.This system must not endanger life or property during the running failure or its security risks
have been eliminated.
Specification
Working voltage: 12-265V AC/DC
Loading capacity: 1.5W
Weight: 156g
Flashing frequency: 1Hz
Installation method: Vertical/horizontal
Working temperature: -20°C~+60°C
Protection level: IP54
Size: 60*85mm
Notice：
1,Terminal 1 is for connectino thepower input; working voltage is 12-265VAC/DC.
2,Terminal 2 is for connecting the antenna of RF controller to extend the effective working distance
Instruction:
After power the lamp on, LED will start fashing in 1HZ(default setting).
sW1 is the switch for selecting flashing or on mode of the lamp.CAP short connectsthe 2 pins; the lamp is in flashing mode. Remove the CAP from 2 pins, the lamp is inon mode.
Be Careful, the whole board includes the components are with high voltage. Alwaysmake sure power is off before you open the cover
Installation
Open the package; take out the products and all the accessories. Removing the antenna by rotatinganticlockwise.
Mark 2 holes on the wall by using the fixing hole of bracket.
Drilling two 6mm diameter holes and one 10mm diameter hole. Then put the expansion plug intothe 6mm diameter holes. Put the wires through 10mm diameter hole.
Put the power wire and antenna through the cable holes in the holder. And fix the holder to thewall by provided 4mm*30mm self-taping screws.
Connect the wire and antenna to the correct terminals.
Put the cover back and make sure the cover is fastened with the bottom base without any gap.Then screw the antenna up and turn clockwise to make it tight.
Always install the holder and lamp upright to the ground. Horizontally installation may cause therain go inside the lam and damage the board.
Mutiple Voltage Flash Lamp
Antenna This is used to extend the effective distance of controller Waterproof and dustproof It is made of plastic material IP 54 .
wide range of uses:
Garage doors, Electronic gates, Barrier gates, sliding doors, automatic doors, rolling doors, shutters
Electrical appliances/Home automation i.e. lights, Alarm system, access control system