Стекло сенсорного экрана 8,4 дюйма подходит для экрана сопротивления автомобиля Chrysler 300 Dodgeloway JEEPGhibli

1.外形 Shape

外形、结构和尺寸详见图纸

Shape, structure and dimension are referred to attached drawing

 

1.1 结构 Structure

结构 Structure

所用材料 Material used

备注 Remark

上线  Top Circuit

ITO 薄膜 ITO FILM

雾面防牛; 单层膜;厚度: 0.188mm

Clear Hard-coating;Double Layer;

Pair Thickness: 0.188mm

下线 Bottom Circuit

ITO GLASS

厚度: 1.1mm

Thickness: 1.1mm

 

1.2 外形尺寸 Shape dimension

项目 Item

尺寸 Dimension

单位 Unit

外形尺寸 Out Dimension

164.9*100

mm

可视区 View Area

157.1*89.6

mm

绝缘点间隔

Spacer Dots Pitch

3*3

mm

 

2.特性 Characteristics

2.1使用、保存环境 Operation and storage

项目 Item

值(条件) Value (conditions)

备注 Remark

使用温度范围

Operation temperature

& Humidity

湿度 20％～90％： 非结露状态

－10℃～60℃

Humidity：20-90％ non dew condensation

－10℃～60℃

单体状态下

In a single substance

保存温度范围

Storage temperature

& Humidity

湿度 20％～90％： 非结露状态

－20℃～70℃

Humidity：20-90％ non dew condensation

－20℃～70℃

单体状态下

In a single substance

2.2电气特性 Electrical characteristics

项目Item

值 Value

备注 Remark

最大电压 Maximum voltage

直流7V DC7V

 

端子间阻抗

Resistance between terminals

Ｘ方向(Film面)：180～900Ω

X direction [Film side]: 180～650Ω

 

Ｙ方向(Glass面)：180～900Ω

Y direction [Glass side]: 180～900Ω

 

直线性

Linearity

Ｘ方向：≤3% 以内

X direction: within ≤2%

测试方法如图所示

Testing method as following drawing

Ｙ方向：≤3% 以内

Y direction: within ≤2%

      

线性Linearity= ︳｛(Vp-Vx) / (Va-Vb)｝︳x100〔%〕

Va= 起点输入电压 Input voltage at start point

Vb= 终点输入电压 Input voltage at end point

测试力 Test force:150gf

绝缘阻抗

Insulation resistance

直流 25Ｖ 10MΩ以上

DC 25V 10MΩ or more

连接X+ ~ X-和Y+ ~ Y-,使用 25V DC 在 X 和Y 测试。

Connect X+ ~ X- and Y+ ~ Y-, apply 25V DC between X and Y for perform measurements

响应时间

Chattering

10 毫秒以下

10 msec or less

 

额定电压

Rated Voltage

直流 5V

DC 5V

 

2.3 机械特性 Mechanical characteristics

项目 Item

性能 Performance

Remark 备注

输入方法

Input method

用专用笔或手指触控

Use of an exclusive pen or finger

 

动作荷重

Load upon operation

专用笔

Exclusive pen

150g 以下

150g or less

使用笔来进行操作或测试时，其笔尖端材质必须符合以下条件：笔尖材质：Polyacetal（聚纤维酯）

笔 端：笔径 Φ3.0 mm 、表面弧度SR 0.8 mm

Operation and measurement with a pen must be carried out under the following tip conditions : Stylus pen material:POM (Polyacetal)

Tip:Diameter3.0mm, SR0.8mm

手指输入

Finger

150g 以下

150g or less

使用特定工具来代替手指进行操作和测试，其材质必须符合以下条件

Operations and measurement methods simulated for a finger must be carried out under the following tip conditions :

材 质：硅橡胶(硬度: 30°Hs)

顶 端：笔径 Φ12mm、表面弧度SR12.5mm

Material: Silicon rubber(Hardness : 30°Hs)

Tip: Diameter12.0mm, SR12.5mm

表面硬度

Surface hardness

铅笔硬度3H 以上

Pencil hardness: 3H or more

依据JIS K5600试验方法

 It complies with the way of test method JIS K5600

备注: 由绝缘点的大小及间距来决定操作压力的大小。

Remark: The operation force depending on the diameter & pitch of spacer dot.

2.4 光学特性 Optical characteristics

项目 Item

性能 Performance

备注 Remark

Total light transmittance

全光线透过率

80%以上

80% or more

JIS K7105

雾值

Haze

3%以下

3% or less

JIS K7136

Film规格

Film specification

雾面防牛防刮 ，有一定表面硬度

Clear Hard-coating,type with hard-coating surface

 

3.信耐性测试                

3.1 环境实验 Environment Test

项目

Items

内容

Contents

备注 Remark

高温保存

High temperature preservation

 

(1)温度80℃,放置240小时；(2)室温放置24小时以上；(3)然后测量以下项目：

(1)Store at 80℃ for 240 hours; (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items: 

端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item

 

低温保存

Low temperature preservation

 

(1)温度－30℃,放置240小时；(2)室温放置24小时以上；(3)然后测量以下项目： 

(1)Store at -30℃ for 240 hours; (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items:

端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item

 

高温高湿保存

High temperature & high humidity

 

(1)温度60℃ 湿度90%,放置240小时；(2)室温放置24小时以上(3)然后测量以下项目:

(1)Store at 60℃and 90% RH for 240 hours; (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items:

端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item

 

冷热冲击测试Heat shook test

(1)－30℃(30 分钟)→80℃(30 分钟)共100次循环;(2)室温放置24小时以上;(3)然后测量以下项目：

(1)－30℃(30min)→80℃(30min)total 100 cycles, (2) Keep at a room temperature for more than 24 hours; and (3) Measure (satisfy) the following items:

端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item

 

 3.2 Durability Test 耐久试验

                                

项目 Items

内容 Contents

备注 Remark

耐敲击

Hitting Durability

 

(1)使用Placental (POM)铅笔(R0.8) 敲击100 万次。(2)然后测量以下项目：

(1)Hit 1,000,000 times with a Placental (POM) pencil (R0.8); and (2) Measure (satisfy) the following items:

荷重：250gf           Load:250gf

速度：2次／sec     Speed: 2 times/sec

端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item

 

耐久划线

Sliding Durability

 

(1)使用Placental (POM)铅笔(R0.8)在AA区域边缘内缩3mm往复划线性10万次；(2)然后测量以下项目：

(1)Shuttle 100,000 times with a Placental (POM) pencil (R0.8) shrinks 3mm from the AA verge; and (2) Measure(satisfy) the following items:

荷重：250gf          Weight:250gf   

速度：100mm／sec Speed: 100mm/sec

端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance: refer to electrical characteristics item

 

FPC 弯曲

FPC Bending durability

(1) 在FPC末端附上100g力；(2)接着以附着力的部分作为弯曲中心(各弯曲180 度5 回)。结果应该满足以下几项：

(1) Attach a 100 g weight to the end of FPC; (2) Bend the FPC at the angle of ±180°each for 5 times, with the FPC adhered portion as the center of bending movement.

The result shall satisfy the following items:

端子间阻抗：参照电气特性栏Resistance between terminals: refer to electrical characteristics item; 直线性：参照电气特性栏 Linearity: refer to electrical characteristics item; 绝缘阻抗：参照电气特性栏 Insulation resistance : refer to electrical characteristics item

 

FPC 拉力测试

FPC Heat Seal Peeling Testing

(1) 垂直90°方向：0.5千克力5分钟；不可剥离；应满足以下项目：

端子间阻抗：参照电气特性栏；

Verticality 90°direction: After 0.5Kg 5min there is no peeling; The result shall satisfy following items:

Resistance between terminals: refer to electrical characteristics item

 

 

(2) 水平180°方向：0.5千克力10分钟；不可剥离；应满足以下项目：

端子间阻抗：参照电气特性栏；

Horizontal 180°direction: After 0.5Kg 10min there is no peeling; The result shall satisfy fallowing items:

Resistance between terminals: refer to electrical characteristics item

 

 

金手指处焊接性

Gold-finger sold heat

温度：320+/-5℃；时间：3-5秒；焊点光滑圆润

Temperature: 320+/-5℃; Time: 3 – 5 sec, sold-dot smooth surface