GoBozor ga xush kelibsiz
Импортный материал encore разрядная игла, оригинальное качество Norsin электродная игла, encore модель круглый электрод плоский
0.0
0 ta sotildi
Eng kam miqdor: 100 dona
Price section
dan boshlab
470 206 so'm
Технические характеристики
стандарт
470 206 so'm
480 availableKafolatlangan yetkazib berish muddati
Agar biz 45 kun kechiksak, buyurtmani bepul olasiz. Batafsil
Har doim siz bilan aloqada
Biz har kuni savollarga har qanday savollarga javob beramiz.
To'lovni qulay usulda xavfsiz qiling
Biz to'lovlarni turli xil usullarda qabul qilamiz.
Bo'lib to'lash mavjud
maxsulotni tanlang
maxsulotni tanlang
Buyurtmani rasmiylashtirish paytida muddatli to‘lovni tanlang. Muddatli to‘lovning yakuniy qiymati rasmiylashtirishda hisoblanadi.
Импортный материал encore разрядная игла, оригинальное качество Norsin электродная игла, encore модель круглый электрод плоский
Mahsulot haqida
Xususiyatlar
- Номер товара
NORSON
- Бренд
другое
- модель
encore
- Цель
Разрядный штифт Джексина
- Алисы
Игла пистолета Nixin
- Импортировано ли оно?
Нет
- Обработка и настройка
Да
- Номер заказа
TF990886790-08
Tavsif
Changing Flat Spray Nozzles
WARNING: Release the spray gun trigger, put the controller to sleep, and
ground the electrode before performing this procedure. Failure to observe
this warning could result in a severe electrical shock.
NOTE: The tapered electrode holder of the electrode assembly has been
designed for optimized cleaning during color changes on systems using flat
spray nozzles. This tapered electrode holder will not accept conical
deflectors.
1. Purge the spray gun and press the Enable/Disable button to put the
controller to sleep in order to prevent accidental gun triggering.
2. See Figure 4-6. Unscrew the nozzle nut counterclockwise.
3. Pull the flat spray nozzle off the electrode assembly.
NOTE: Re-install the electrode assembly if it comes out of the powder
outlet tube.
4. Install a new nozzle on the electrode assembly. The nozzle is keyed to
the electrode assembly. Do not bend the antenna wire.
5. Screw the nozzle nut onto the gun body clockwise until finger-tight.
6. Press the Enable/Disable button to wake up the controller.
NOTE: To clean nozzles, use the Recommended Cleaning Procedure for
Powder Contact Parts on page 4-10.
Nozzle Nut Flat Spray Nozzle Flat Spray Electrode Assembly
Figure 4-6 Changing a Flat Spray Nozzle
Changing Deflectors or Conical Nozzles
WARNING: Release the spray gun trigger, turn off the interface, and
ground the electrode before performing this procedure. Failure to observe
this warning could result in a severe electrical shock.
NOTE: The electrode assembly shipped with the gun is fitted with a
tapered electrode holder that will not accept a conical deflector and must be
changed prior to using the conical nozzle and deflector. Follow the
instructions in the conical nozzle kit shipped with the gun for this conversion.
1. Purge the spray gun and turn off the interface in order to prevent
accidentally triggering the gun on.Operation
4-9
Part 1603227-12
2016 Nordson Corporation
2. See Figure 4-7. Gently pull the deflector off the electrode holder. If only
changing the deflector, install the new one on the electrode holder, being
careful not to bend the electrode wire.
3. To change the entire nozzle, unscrew the nozzle nut counterclockwise.
4. Pull the conical nozzle off the electrode assembly.
NOTE: If the electrode assembly comes out of the powder outlet tube,
re-install it.
5. Install a new conical nozzle on the electrode assembly. The nozzle is
keyed to the electrode assembly.
6. Screw the nozzle nut onto the gun body clockwise until finger-tight.
7. Install a new deflector on the electrode assembly. Do not bend the
electrode wire.
Barcha xususiyatlar
Xususiyatlari
- Номер товара
NORSON
- Бренд
другое
- модель
encore
- Цель
Разрядный штифт Джексина
Tavsif
Changing Flat Spray Nozzles
WARNING: Release the spray gun trigger, put the controller to sleep, and
ground the electrode before performing this procedure. Failure to observe
this warning could result in a severe electrical shock.
NOTE: The tapered electrode holder of the electrode assembly has been
designed for optimized cleaning during color changes on systems using flat
spray nozzles. This tapered electrode holder will not accept conical
deflectors.
1. Purge the spray gun and press the Enable/Disable button to put the
controller to sleep in order to prevent accidental gun triggering.
2. See Figure 4-6. Unscrew the nozzle nut counterclockwise.
3. Pull the flat spray nozzle off the electrode assembly.
NOTE: Re-install the electrode assembly if it comes out of the powder
outlet tube.
4. Install a new nozzle on the electrode assembly. The nozzle is keyed to
the electrode assembly. Do not bend the antenna wire.
5. Screw the nozzle nut onto the gun body clockwise until finger-tight.
6. Press the Enable/Disable button to wake up the controller.
NOTE: To clean nozzles, use the Recommended Cleaning Procedure for
Powder Contact Parts on page 4-10.
Nozzle Nut Flat Spray Nozzle Flat Spray Electrode Assembly
Figure 4-6 Changing a Flat Spray Nozzle
Changing Deflectors or Conical Nozzles
WARNING: Release the spray gun trigger, turn off the interface, and
ground the electrode before performing this procedure. Failure to observe
this warning could result in a severe electrical shock.
NOTE: The electrode assembly shipped with the gun is fitted with a
tapered electrode holder that will not accept a conical deflector and must be
changed prior to using the conical nozzle and deflector. Follow the
instructions in the conical nozzle kit shipped with the gun for this conversion.
1. Purge the spray gun and turn off the interface in order to prevent
accidentally triggering the gun on.Operation
4-9
Part 1603227-12
2016 Nordson Corporation
2. See Figure 4-7. Gently pull the deflector off the electrode holder. If only
changing the deflector, install the new one on the electrode holder, being
careful not to bend the electrode wire.
3. To change the entire nozzle, unscrew the nozzle nut counterclockwise.
4. Pull the conical nozzle off the electrode assembly.
NOTE: If the electrode assembly comes out of the powder outlet tube,
re-install it.
5. Install a new conical nozzle on the electrode assembly. The nozzle is
keyed to the electrode assembly.
6. Screw the nozzle nut onto the gun body clockwise until finger-tight.
7. Install a new deflector on the electrode assembly. Do not bend the
electrode wire.